Utilize este identificador para citar ou criar um atalho para este documento: https://hdl.handle.net/10923/567
Tipo: masterThesis
Título: Influência da fadiga cíclica de instrumentos rotatórios de NiTi em canal curvo simulado
Autor(es): Carvalho, Henrique Parente de
Orientador: Mota, Eduardo Gonçalves
Editora: Pontifícia Universidade Católica do Rio Grande do Sul
Programa: Programa de Pós-Graduação em Odontologia
Data de Publicação: 2010
Palavras-chave: ODONTOLOGIA
ENDODONTIA
MATERIAIS DENTÁRIOS
RESISTÊNCIA DOS MATERIAIS (ODONTOLOGIA)
Resumo: Os objetivos deste estudo foram avaliar e comparar instrumentos endodônticos rotatórios de NiTi de duas marcas comerciais distintas quanto a resistência a fadiga cíclica, microestrutura, morfologia externa, onde vinte limas rotatórias de níquel-titânio novas, foram levadas à análise. Estas limas foram distribuídas em dois grupos, de acordo com o sistema, sendo o primeiro composto de 10 limas K3 (SDS Kerr, Glendora, CA EUA), e o segundo, por 10 limas Profile (Maillefer, Ballaiques, Suiça). As dimensões das limas testadas são correspondentes às especificações 25. 06 (diâmetro na ponta igual a 0,25mm, e conicidade 0,06). Foram feitas observações das limas por microscopia eletrônica de varredura, com análise de EDS, para caracterização das condições superficiais do material como fornecido. A superfície de corte e a microestrutura também foram analisadas. Após esta análise, as amostras foram submetidas a um ensaio de fadiga por flexão através de um sistema composto por um canal artificial metálico com um ângulo de curvatura de 90 graus e um motor elétrico onde o contra-ângulo foi conectado. O protocolo de velocidade estabelecido foi de 350 RPM. As limas foram inseridas em movimento rotatório, até o momento da fratura. O registro de tempo foi realizado com um cronometro digital até o momento da fratura. O número de ciclos necessários para fratura da lima foi calculado através da relação tempo e rotações por segundo até a fratura de cada instrumento.Os vinte fragmentos recuperados foram medidos (mm) através de um paquímetro digital. Com base nas observações deste estudo, pode-se constatar que as limas apresentam a mesma composição superficial e padrão de microestrutura, entretanto, os instrumentos se diferem quanto à morfologia externa. Sob a condição experimental do estudo atual, o sistema Profile apresentou a resistência à fadiga cíclica significativamente maior quando comparada ao do sistema K3, testadas em uma curvatura abrupta de 90º. A lima K3 apresentou média de 547 enquanto a Profile apresentou média de 807. Quanto ao tamanho dos fragmentos não houve qualquer relação entre as diferentes propostas. Pode-se concluir que as limas apresentam a mesma composição superficial e padrão de microestrutura, entretanto se diferem quanto à morfologia externa.
The objectives of this study were to evaluate and to compare rotatory instruments of NiTi from two different commercial brands, where twenty new nickel-titanium endodontic rotatory alloys were taken to the analysis. These alloys were distributed in two groups, in agreement with the manufacturer, being the first composed by 10 K3 alloys (SDS Kerr, Glendora, CA EUA), and the second, by 10 Profile alloys (Maillefer, Ballaiques, Switzerland). The dimensions of the tested alloys are corresponding to the specifications 25. 06 (diameter in the tip equal to 0,25mm, and taper 0, 06). Observations of the alloys were made by electronic microscopy of scintiscan, with analysis of SDE, for characterization of the superficial conditions of the material as provided. The cut surface and the microstructure were also analyzed. After this analysis, the samples were submitted to a test of fatigue for flexing through a system composed by a metallic artificial canal with an angle of curvature of 90 degrees and an electric engine where the contra-angle was connected. The established protocol of speed was of 350 RPM.The alloys were inserted in rotatories movement, until the moment of the fracture. The registration of time was accomplished with a digital timer and the verification of the occurrence of the fracture of the instrument was visual and hearing. The number of necessary cycles for fracture of the alloy was calculated through the relation time and rotations per second until the fracture of each instrument. The twenty recovered fragments were measured (mm) through a digital pachymeter. Based on the observations of this study, it can be verified that the alloys present the same superficial composition and pattern, however, the instruments differed themselves related to the external morphology. Under the experimental condition of the current study, the Profile system presented resistance to cyclical fatigue significantly larger when compared to the K3 system, tested in an abrupt curvature of 90º. The K3 alloy presented average of 547 while Profile presented average of 807. Related to the size of the fragments there was no any relation among the different proposals.
URI: http://hdl.handle.net/10923/567
Aparece nas Coleções:Dissertação e Tese

Arquivos neste item:
Arquivo Descrição TamanhoFormato 
000428359-0.pdfTexto Completo568,6 kBAdobe PDFAbrir
Exibir


Todos os itens no Repositório da PUCRS estão protegidos por copyright, com todos os direitos reservados, e estão licenciados com uma Licença Creative Commons - Atribuição-NãoComercial 4.0 Internacional. Saiba mais.